HEAT TRANSFER FLUIDS    

 YOUR HEAT TRANSFER NEEDS ARE OUR ONLY CONCERN
"The Exception To The Rule"
MultiTherm® Heat Transfer Fluids
 
 

Heat Transfer Fluids: High Temperature Applications

MultiTherm PG-1®

  • Operating range from 10°F (-12°C) to 600°F (315°C)
  • Food grade (NSF registered, FDA certified Non-Toxic, USDA Chemicallyacceptable, Kosher certified)
  • Low viscosity / Low pour point
  • Non-Toxic, Non-Hazardous, Non-Fouling
  • Designed for applications in Food, Chemical, Plastics, and Die-Casting
  • Thermal expansion coefficient 0.00035/ÁF (0.00063/ÁC)
  • For use in closed loop, liquid phase heating and cooling systems to 600°F

  MultiTherm OG-1®
  • MultiTherm's oxidation grade fluid for open or closed loop systems
  • Operating range from 10°F (-12°C) to 550°F (290°C)
  • Highly refined to have High flash point
  • Oxidation resistant - Very Low vapor pressure
  • Non-Toxic, Non-Hazardous
  • Designed for applications where the hot heat transfer fluid comes in contact with atmosphere
  • Thermal expansion coefficient 0.00056/ÁF (0.00102/ÁC)

MultiTherm 503®
  • When you have heating and cooling in the same loop
  • Operation range: from 50°F (-10°C) to 500°F (260°C)
  • Meets FDA specifications but not certified
  • Very low viscosity - Very low pour point - Low vapor pressure
  • Relatively high flash point - Non-Toxic, Non-Hazardous
  • Designed for applications in Plastics, Chemical, and other processing industries
  • Thermal expansion coefficient 0.00051/ÁF (0.00092/ÁC)
  • For use in closed loop, liquid phase heating and cooling systems from 10°F to 500°F

MultiTherm IG-4®
  • Operating range from 10°F (-12°C) to 600°F (315°C)
  • Highly refined to have High flash point
  • Oxidation resistance - Very Low vapor pressure
  • Non-Toxic, Non-Hazardous
  • Designed for applications in Asphalt, Chemical, Plastics, Laundries and Die-Casting
  • Thermal expansion coefficient 0.00054/ÁF (0.00097/ÁC)
  • For use in closed loop, liquid phase heating systems up to 600°F
  • MultiTherm IG-4 is an upgrade of, and a direct replacement for MultiTherm IG-2®

MultiTherm IG-1®  
  • Operating range from 10°F (-12°C) to 550°F (288°C)
  • Economical heat transfer fluid
  • High flash point
  • Non-Toxic, Non-Hazardous
  • Designed for applications in Asphalt, Roofing, Paper, Particle Board and Die-Casting
  • Thermal expansion coefficient 0.00054/ÁF (0.00098/ÁC)
 

Heat Transfer Fluids: Low Temperature Applications

MultiTherm ULT-170®

  • For ultra low temperature applications
  • Operation range down to -170°F (-112°C)
  • Low freezing point - Low viscosity at ultra-low temperatures
  • Thermally stable & biodegradable
  • Single fluid usage for sterilization applications
  • Designed for Pharmaceutical, Chemical, Freeze-Drying, and Cryogenic applications
  • Extends low-end operating ranges far beyond the boundaries of most competitive brands
  • Remains pumpable even at temperatures below -170°F (-112°C)

MultiTherm WB®

  • Aqueous-based for Low temperature applications
  • Operation range down to -58°F (-50°C)
  • Non-toxic, None-flammable
  • Designed for Ice Rink, Food, Refrigeration, Breweries/Distilleries, and HVAC applications
  • Engineered to deliver the desirable low-end temperature performance of synthetic organic and silicone-based fluids
 

Heat Transfer Flushing/Cleaning Fluid

MultiTherm FF-1®

  • Specially formulated flushing fluid to clean out systems during:
    • Start-ups - to remove loose material such as weld splatter, fines, particulate matter, etc. left in lines and equipment, along with oil and some preservative coatings
    • General Maintenance - for removing particulate matter and used heat transfer fluid from a system prior to recharge or changeover from one fluid to another.
  • Compatible with all MultiTherm and mineral oil heat transfer fluids.
  • Thermal expansion coefficient 0.00047/ÁF (0.00085/ÁC)
MultiTherm PSC Plus®
  • More Economical for Large Systems
  • Higher Flash Point then other typical System Cleaners
  • Non-Corrosive, Non-Toxic and Non-Hazardous material
  • Designed to breakdown sludge and stay in suspension for
    easy removal or filtration. System can be operated up to 550ºF/288ºC.
 

 Heat Transfer Filtration
 Hot Oil Filtration Systems

 

HVAC/Industrial Coils

Replacement or New


 

Chilled Water, Hot Water, Steam, DX or Condenser

Heavy duty industrial coils of all types

  • Duplicate existing dimensions and performance
  • Special 5 work day and 10 work day quick shipments available
  • Hot water duct booster coils in stock
  • Call 800-225-7440 for immediate pricing, technical information and delivery information
 

T-Bar Unit Self Contained AC Unit



A T-Bar Unit from Multitherm is the answer to your special cooling and dehumidification needs. And, it fits right into a standard 2' x 4' suspended ceiling panel, with no floor space needed.

 

JUNIORFLUX Pump & Motor Unit/PP From MultiTherm



For filling, emptying, transferring or dispensing small amounts of liquid out of carboys, hobbocks, canisters, narrow-necked containers or barrels FLUX now offers a better performance: the new JUNIORFLUX pumps type F 310 and F 314.

The JUNIORFLUX pumps are available in polypropylene (PP), polyvinylidene fluoride (PVDF) or stainless steel (S), both in version with mechanical seal Type F 310 or sealless Type F 314.

A powerful 230 Watt commutator motor with a 2-speed switch allows sensitive, fast and therefore low-cost and safe filling operations. The motor is built to protection class II, splash-proof and comprises an overload cut-out switch. Another feature is the modern and ergonomically structured design for single-hand operation.